Welcome to Australia's only Vintage Radio and Television discussion forums. You are not logged in. Please log in below, apply for an account or retrieve your password.
Australian Vintage Radio Forums
  Home  ·  About Us  ·  Discussion Forums  ·  Glossary  ·  Outside Links  ·  Policies  ·  Services Directory  ·  Safety Warnings  ·  Tutorials

Wanted and For Sale

Forum home - Go back to Wanted and for sale

 Wanted 1 EM1 tuning valve
« Back · 1 · 2 · Next »
 Return to top of page · Post #: 16 · Written at 11:51:52 PM on 23 August 2018.
GTC's avatar
 GTC
 Location: Sydney, NSW
 Member since 28 January 2011
 Member #: 823
 Postcount: 6761

I do have a New old stock one coming

If it's in working condition, then that would have attracted a good price.
 
 Return to top of page · Post #: 17 · Written at 12:44:14 AM on 24 August 2018.
Tallar Carl's avatar
 Tallar Carl
 Location: Latham, ACT
 Member since 21 February 2015
 Member #: 1705
 Postcount: 2174

$40.00 it cost me. And I have seen it working. They do attract a much higher price but it was a fellow that I have helped in the past.
 
 Return to top of page · Post #: 18 · Written at 10:11:42 AM on 24 August 2018.
STC830's Gravatar
 STC830
 Location: NSW
 Member since 10 June 2010
 Member #: 681
 Postcount: 1301

Good result.

My EM4s I had marked down as NOS? ie possibly used given the state of the paint (badly cracked) on one of them. The target looks OK though. The box was open on the other so it could have been swapped out; again target looks OK.
 
 Return to top of page · Post #: 19 · Written at 12:05:06 PM on 24 August 2018.
GTC's avatar
 GTC
 Location: Sydney, NSW
 Member since 28 January 2011
 Member #: 823
 Postcount: 6761

$40 is a low going by what they are asking on the web.
 
 Return to top of page · Post #: 20 · Written at 5:06:36 PM on 24 August 2018.
Tallar Carl's avatar
 Tallar Carl
 Location: Latham, ACT
 Member since 21 February 2015
 Member #: 1705
 Postcount: 2174

GTC the reason I got such a good price is because I had helped the gentleman with other parts that he needed to complete some of his restorations ( this was some time back ).
This is the way this hobby should always be. Mind you I would have paid much more as I believe a good service should be paid for. I have seen a untested and very rough looking example on ebay for the same price and from europe.
 
« Back · 1 · 2 · Next »
 You need to be a member to post comments on this forum.

Sign In

Username:
Password:
 Keep me logged in.
Do not tick box on a computer with public access.

Vintage Radio and Television is proudly brought to you by an era where things were built with pride and made to last.

DISCLAIMER: Valve radios and televisions contain voltages that can deliver lethal shocks. You should not attempt to work on a valve radio or other electrical appliances unless you know exactly what you are doing and have gained some experience with electronics and working around high voltages. The owner, administrators and staff of Vintage Radio & Television will accept no liability for any damage, injury or loss of life that comes as a result of your use or mis-use of information on this website. Please read our Safety Warning before using this website.

WARNING: Under no circumstances should you ever apply power to a vintage radio, television or other electrical appliance you have acquired without first having it checked and serviced by an experienced person. Also, at no time should any appliance be connected to an electricity supply if the power cord is damaged. If in doubt, do not apply power.

Shintara - Keepin' It Real · VileSilencer - Maintain The Rage