What wire and where to buy it in Australia
|
« Back ·
1 ·
Next »
|
|
|
Location: Brisbane, QLD
Member since 12 November 2015
Member #: 1824
Postcount: 20
|
Hi Guys,
Had a search around (Internet and the forum) but haven't managed to find any wire that I am happy to use inside the chassis of the radiogram I am repairing. I need red and yellow to replace the perished internal wiring on the valve chassis. I assume 300V 105 degrees is needed and something like 16AWG?
Does anybody know of a source without having to buy 100M of the stuff?
Thanks,
Glenn.
|
|
|
|
Location: Donald, VIC
Member since 7 January 2006
Member #: 13
Postcount: 265
|
I have the wire you need Glenn iam out of stock but will have more soon
‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾
Steve.
|
|
|
|
Location: Sydney, NSW
Member since 28 January 2011
Member #: 823
Postcount: 6687
|
|
|
|
|
Location: Wangaratta, VIC
Member since 21 February 2009
Member #: 438
Postcount: 5254
|
Whilst most wire will stand more than its rated voltage. Valve radios with filament rectifiers & Solid state rectifiers that produce voltage before the heater valves start to conduct, can get to 500VDC
From memory EVATCO's cloth type stuff was 600V. should be on the site. Assume Steve's is similar?
Also consider that when replacing Electrolytics on the "B" rail.
Accuracy of advice depends on what you tell us.
Marc
|
|
|
|
Location: Sydney, NSW
Member since 28 January 2011
Member #: 823
Postcount: 6687
|
From memory EVATCO's cloth type stuff was 600V.
Yes, it is.
should be on the site
It is, simply follow the link I posted.
|
|
|
|
Location: Donald, VIC
Member since 7 January 2006
Member #: 13
Postcount: 265
|
Evatcos is same ( they got theirs from me originally ) I don't keep much anymore of the restoration lines, unless the orders are world beaters in volume. Its not really worth my while you know !
A new knob il have in soon, very very rare and il have several 100 of those.
‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾
Steve.
|
|
|
|
Location: Wangaratta, VIC
Member since 21 February 2009
Member #: 438
Postcount: 5254
|
Think we have this under control even that we have no idea what it is? I will probably need a cap re-stock soon.
How things have changed with caps. I have a Grigsby-Grunow (1932) on the bench & that has two 8μF filters (Non Polarised) 100 x 30 x 50mm. The last set (1929) similar had a 50 OP valve & that had over 300V on the plate (max 450V with -84v on the grid (separate rectifier on its own winding) needed to watch the fingers with that one.
Marc
|
|
|
|
Location: Brisbane, QLD
Member since 12 November 2015
Member #: 1824
Postcount: 20
|
Sorry Marc, the details of the unit are in a separate Newbie thread, I should have added it in here. Mullard MAS1153. Original wires are multi-strand rubber coated. Replacing all caps except Mica, plus power cord and a broken dial string, and now internal wiring. The evatco link listed is a single strand, but there is multi-strand on their site.
Steve has kindly responded, but he is out of stock and my tiny order isn't enough to get him out of retirement... (joke ).
|
|
|
|
Location: Wangaratta, VIC
Member since 21 February 2009
Member #: 438
Postcount: 5254
|
I have used EVATCO wire. You can actually buy the plug & cable (suicide cable) as one piece & thats actually cheaper if your not fussy & I will often recycle a scrapped IEC cable from a computer that has been tossed.
Just cut the IEC plug off & you have a good cable with a moulded plug. I tend to use glands for the mains wire. Most times it can be put in pointy end inside the pan & that stops the cable twisting.
For general running around buy stranded in more than one colour. To make life easier I normally use Orange on DC before the B+ choke red for the direct B+ after the choke & blue on the RF screens. That makes it easier to follow.
A bit of circuit board lacquer, or shrink tube (band) stops it fraying at the ends.
|
|
|
|
Location: Sydney, NSW
Member since 28 January 2011
Member #: 823
Postcount: 6687
|
|
|
« Back ·
1 ·
Next »
|
You need to be a member to post comments on this forum.
|