Welcome to Australia's only Vintage Radio and Television discussion forums. You are not logged in. Please log in below, apply for an account or retrieve your password.
Australian Vintage Radio Forums
  Home  ·  About Us  ·  Discussion Forums  ·  Glossary  ·  Outside Links  ·  Policies  ·  Services Directory  ·  Safety Warnings  ·  Tutorials

Tech Talk

Forum home - Go back to Tech talk

 American valve radios for use in Australia
« Back · 1 · 2 · Next »
 Return to top of page · Post #: 16 · Written at 11:02:12 PM on 9 August 2017.
Robbbert's avatar
 Robbbert
 Location: Hill Top, NSW
 Member since 18 September 2015
 Member #: 1801
 Postcount: 2078

Quote from Wikipedia.

1978:

- All AM radio station frequencies are changed from 10 kHz to 9 kHz under the Geneva Frequency Plan of 1975.
- 2WS Sydney (1224) begins broadcasting

...

1984:

- Stereo AM radio transmission is launched
 
 Return to top of page · Post #: 17 · Written at 9:17:42 AM on 10 August 2017.
Wa2ise's avatar
 Wa2ise
 Location: Oradell, US
 Member since 2 April 2010
 Member #: 643
 Postcount: 831

As most American radios back then were all hot chassis design, the best solution would be to use a 240V to 120V isolation transformer. And radios of this vintage will need to be recapped, ie, replace the wax paper caps and electrolytic power supply caps. The tubes will probably be good, unused or idle tubes not powered will last forever, but not so for wax caps. American radios usually have internal loop antennas, few had the need for external long wire antennas.
 
 Return to top of page · Post #: 18 · Written at 4:02:41 PM on 10 August 2017.
Tallar Carl's avatar
 Tallar Carl
 Location: Latham, ACT
 Member since 21 February 2015
 Member #: 1705
 Postcount: 2174

Resurrection Radio in Melbourne is well regarded.
 
 Return to top of page · Post #: 19 · Written at 9:03:13 PM on 11 August 2017.
Marcc's avatar
 Marcc
 Location: Wangaratta, VIC
 Member since 21 February 2009
 Member #: 438
 Postcount: 5389

I do pedantically write: Never power an unknown set. Always inspect it if you do not know its history. If an owner brings in a set barely working fine, often with those you don't have to take a massive risk, as just by description, you know the problem.

There are two examples on my bench, both mentioned elsewhere. viz. HMV E43F & an English Roberts R66. HMV had a wiring error, plus other issues: Never going to work, why power it. Roberts had a can cap leaking: No way, do you power up with one like that, still wired in.

Marc
 
« Back · 1 · 2 · Next »
 You need to be a member to post comments on this forum.

Sign In

Username:
Password:
 Keep me logged in.
Do not tick box on a computer with public access.

Vintage Radio and Television is proudly brought to you by an era where things were built with pride and made to last.

DISCLAIMER: Valve radios and televisions contain voltages that can deliver lethal shocks. You should not attempt to work on a valve radio or other electrical appliances unless you know exactly what you are doing and have gained some experience with electronics and working around high voltages. The owner, administrators and staff of Vintage Radio & Television will accept no liability for any damage, injury or loss of life that comes as a result of your use or mis-use of information on this website. Please read our Safety Warning before using this website.

WARNING: Under no circumstances should you ever apply power to a vintage radio, television or other electrical appliance you have acquired without first having it checked and serviced by an experienced person. Also, at no time should any appliance be connected to an electricity supply if the power cord is damaged. If in doubt, do not apply power.

Shintara - Keepin' It Real · VileSilencer - Maintain The Rage