Welcome to Australia's only Vintage Radio and Television discussion forums. You are not logged in. Please log in below, apply for an account or retrieve your password.
Australian Vintage Radio Forums
  Home  ·  About Us  ·  Discussion Forums  ·  Glossary  ·  Outside Links  ·  Policies  ·  Services Directory  ·  Safety Warnings  ·  Tutorials

General Discussion

Forum home - Go back to General discussion

 32 volt radios
« Back · 1 · Next »
 Return to top of page · Post #: 1 · Written at 8:43:04 PM on 10 March 2011.
32 Volt Radio's Gravatar
 32 Volt Radio
 Location: Sydney, NSW
 Member since 10 March 2011
 Member #: 852
 Postcount: 69

Hi, I'm back with a new password.
I would like to thank the people who replied re 32v radios
a couple of months ago...i made the mistake of thinking there was no interest but only checked for a couple of days. Sorry.
One member mentioned that I should leave my email, which I will here, also I made Astor HMQ comments in the Intro forum...i have a fried one...not beyond help I think.
email.... windlights2000.yahoo.com.au

Thankyou all many regards Michael.
 
 Return to top of page · Post #: 2 · Written at 11:43:15 PM on 10 March 2011.
Marcc's avatar
 Marcc
 Location: Wangaratta, VIC
 Member since 21 February 2009
 Member #: 438
 Postcount: 5389

But what in particular did you fry? Those valves are not very tolerant of over voltage on filaments.

The only thing different with these things, is the power supply. The main body of the radio fails all of the parts an AC one does.

The power supplies are predictable. The last vibrator type PS I repaired was in an Airchief.

Marc
 
 Return to top of page · Post #: 3 · Written at 8:25:37 AM on 11 March 2011.
32 Volt Radio's Gravatar
 32 Volt Radio
 Location: Sydney, NSW
 Member since 10 March 2011
 Member #: 852
 Postcount: 69

I wish it just fried some valves...i wasnt there at the time, but should have known something was up when Dad told me he had to switch a few lights on to get the radio to work.
A quick glance ( total novice) under chassis sees 1/2 dozen wires around one of the valves with melted insulation and a puddle of wax on the floor of the vibrator box from what I assume is a capacitor.
 
 Return to top of page · Post #: 4 · Written at 11:59:47 PM on 11 March 2011.
Marcc's avatar
 Marcc
 Location: Wangaratta, VIC
 Member since 21 February 2009
 Member #: 438
 Postcount: 5389

It never ceases to amaze, as to the damage those who know nothing about radio's can do using their expertise in trying to get a set to run.

One can only hope that the caps took the bulk of the load. The tube filaments can be checked for filament continuity with an ohmmeter. Because in filament valves the heater & cathode are the same I can visualise them cooked.

Marc
 
« Back · 1 · Next »
 You need to be a member to post comments on this forum.

Sign In

Username:
Password:
 Keep me logged in.
Do not tick box on a computer with public access.

Vintage Radio and Television is proudly brought to you by an era where things were built with pride and made to last.

DISCLAIMER: Valve radios and televisions contain voltages that can deliver lethal shocks. You should not attempt to work on a valve radio or other electrical appliances unless you know exactly what you are doing and have gained some experience with electronics and working around high voltages. The owner, administrators and staff of Vintage Radio & Television will accept no liability for any damage, injury or loss of life that comes as a result of your use or mis-use of information on this website. Please read our Safety Warning before using this website.

WARNING: Under no circumstances should you ever apply power to a vintage radio, television or other electrical appliance you have acquired without first having it checked and serviced by an experienced person. Also, at no time should any appliance be connected to an electricity supply if the power cord is damaged. If in doubt, do not apply power.

Shintara - Keepin' It Real · VileSilencer - Maintain The Rage