General Discussion

Forum home - Go back to General discussion

Radio Waves -- October 2019 issue
« Back · 1 · Next »
Return to top of page · Post #: 1 · Written at 12:39:32 AM on 30 October 2019.
	GTC Location: Sydney, NSW Member since 28 January 2011 Member #: 823 Postcount: 6761
The printer was having a bad day when he collated my copy of this issue. Pages go: ..., 17, 18, 29, 30, 21, 22, 23, 24, 25, 26, 27, 28, 19, 20, 31, 32, .... Will have to pull it apart and get Officeworks or a printery to re-staple it for me.

Return to top of page · Post #: 2 · Written at 5:08:53 AM on 30 October 2019.
	Brad Administrator Location: Naremburn, NSW Member since 15 November 2005 Member #: 1 Postcount: 7395
Mine is still in the wrapper so I am not sure if the glitch covers the whole print or not yet. ‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾ A valve a day keeps the transistor away...

Return to top of page · Post #: 3 · Written at 9:47:17 AM on 30 October 2019.
	Marcc Location: Wangaratta, VIC Member since 21 February 2009 Member #: 438 Postcount: 5389
I have two here mine & Radio Club they seem to be OK. However, there is a warning. As I send to Printing establishments the warning is never to send it in MS Word: Even if the other end has the same version of Word it can cause format & other little annoying problems. This has happened to me, that's the primary reason I was made aware of it and everything since (as requested) is sent in the much more stable "Portable Document Format" (Adobe pdf)

Return to top of page · Post #: 4 · Written at 4:01:03 PM on 30 October 2019.
	Brad Administrator Location: Naremburn, NSW Member since 15 November 2005 Member #: 1 Postcount: 7395
Mine is mis-numbered as per GTC's. Not to worry. As long as it is all there... Later on I may try opening the staples and just manually reorganising the pages then close the staples again. ‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾ A valve a day keeps the transistor away...

Return to top of page · Post #: 5 · Written at 8:05:42 PM on 30 October 2019.
	GTC Location: Sydney, NSW Member since 28 January 2011 Member #: 823 Postcount: 6761
then close the staples again I find doing that with a thick magazine never gets them tight enough.

Return to top of page · Post #: 6 · Written at 8:06:20 PM on 30 October 2019.
	Marcc Location: Wangaratta, VIC Member since 21 February 2009 Member #: 438 Postcount: 5389
Looks a bit like a machine hissy fit.

Return to top of page · Post #: 7 · Written at 11:46:52 PM on 30 October 2019.
	Brad Administrator Location: Naremburn, NSW Member since 15 November 2005 Member #: 1 Postcount: 7395
A ball pein hammer will do the trick. ‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾ A valve a day keeps the transistor away...

Return to top of page · Post #: 8 · Written at 7:23:57 PM on 1 November 2019.
	GTC Location: Sydney, NSW Member since 28 January 2011 Member #: 823 Postcount: 6761
Friendly guy at Snap Printing re-stapled mine today.

Return to top of page · Post #: 9 · Written at 8:02:55 AM on 2 November 2019.
	STC830 Location: NSW Member since 10 June 2010 Member #: 681 Postcount: 1301
Mine is in the correct order.

Return to top of page · Post #: 10 · Written at 5:49:16 PM on 2 November 2019.
	Tallar Carl Location: Latham, ACT Member since 21 February 2015 Member #: 1705 Postcount: 2174
I just went to the Canberra HRSA meeting. This subject came up . All you need to do is email Kevin Poulter and he will arrange for a good one to be sent to you. The printer stuffed it up and has to make good with extras.

« Back · 1 · Next »
You need to be a member to post comments on this forum.

General Discussion

Sign In